|
|
|
|
|
|
|
|
|
|
|
|
|
|
System 636 PVC flue gas venting system offers regular and increaser couplings to help meet manufacturers recommended installation practices.
|
Vent screens are added to the hub end of elbows used to terminate exhaust and intake pipe runs on the outside wall of a building to keep dirt, debris and animals out of the venting system.
|
An elbow is installed when a change of direction is needed in a vent line. Two 45 deg elbows can be used in place of a 90 deg elbow if needed.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Use to adjust and balance airflow in individual runs of round pipe.
|
An elbow is installed when a change of direction is needed in a vent line. The 90 deg elbow is a long-radius elbow to reduce the restriction on airflow in the exhaust or intake line.
|
System 636 PVC flue gas venting system offers regular and increaser couplings to help meet manufacturers recommended installation practices.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Imperial Connector Union, 3 in Union, Galvanized Steel, 3 in L x 3 in W x 4 in H Dimensions
|
Used for transition from air plenums or rectangular duct to round pipe or insulated duct. 30 ga.
|
IPEX System 636 Pipe Tee, Nominal Size: 2 in, Hub Connection, Operating Temperature: 65 deg C, PVC
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Imperial Duct Elbow, 6 in Connection, 30 ga, Oval Flat Duct, Galvanized, Dimensions: 12-3/8 in H x 2-3/4 in W
|
Vent screens are added to the hub end of elbows used to terminate exhaust and intake pipe runs on the outside wall of a building to keep dirt, debris and animals out of the venting system.
|
Adjustable 4 piece elbow. Adjusts from straight through 90 deg.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Adjustable 4 piece elbow. Adjusts from straight through 90 deg.
|
Used for right-angle center-end transition from round pipe or insulated flexible duct to a register or grille.
|
Used for in-line transition from round pipe or insulated flexible duct to a register or grille. 30 ga.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
An elbow is installed when a change of direction is needed in a vent line. Two 45 deg elbows can be used in place of a 90 deg elbow if needed.
|
System 636 PVC flue gas venting system offers regular and increaser couplings to help meet manufacturers recommended installation practices.
|
Imperial Connector Union, 6 in Union, Round Duct, Galvanized Steel
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Imperial Connector Union, 4 in Union, Galvanized Steel, 4 in L x 4 in W x 4 in H Dimensions
|
Used to tap into the top of trunk duct. Forms a transition from rectangular to round branch duct. Used when branch ducts are to be located within a joist space. 30 ga.
|
Used to tap into the top of trunk duct. Forms a transition from rectangular to round branch duct. Used when branch ducts are to be located within a joist space. 30 ga.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Used for transition from air plenums or rectangular duct to round pipe or insulated duct. 30 ga.
|
Used to tap into the top of trunk duct. Forms a transition from rectangular to round branch duct. Used when branch ducts are to be located within a joist space. 30 ga.
|
Imperial Angle Boot, 90 deg, Steel, Galvanized, 3 in L, 10 in W, 6 in H
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Used for in-line transition from round pipe or insulated flexible duct to a register or grille. 30 ga.
|
Used for right-angle center-end transition from round pipe or insulated flexible duct to a register or grille.
|
Used for in-line transition from round pipe or insulated flexible duct to a register or grille. 30 ga.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Used for in-line transition from round pipe or insulated flexible duct to a register or grille. 30 ga.
|
Imperial Connector Union, 5 in Union, Galvanized Steel, 5 in L x 5 in W x 4 in H Dimensions
|
Imperial Oval Vertical Elbow, Material Gauge: 30 ga, Steel, Galvanized, Dimensions: 6 in Dia
|
|
|
